Push-Fit Fittings

Flow Control

material

brand

categoryId

stockStatus

Water Control

John Guest Speedfit

Connects plain pipe end to end and smaller diameter pipe at 90.

Connects plain pipe end to end and smaller diameter pipe at 90°.

Push-fit Solution for Plumbing & Heating Systems
For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291.
NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. 
Standards Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit ‘PEM’ and ‘PKM’ fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767).
Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings.
Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. 
Speedfit products, when used indoors, are not affected by sunlight. 
When used outdoors protect from ultra violet light by lagging or painting.
It is recommended that all installations are checked prior to use to determine that a seal has been made.

Push-fit Solution for Plumbing & Heating Systems - Reducing Tees

15x15x10mm SPEEDFIT REDUCING TEE

For securing pipe safely to walls. Not to be fitted any closer than 60mm from pipe end fitting

For securing pipe to walls.
NOT TO BE FITTED ANY CLOSER THAN 60mm FROM END OF FITTING

Push-fit Solution for Plumbing & Heating Systems
For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291.
NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. 
Standards Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit ‘PEM’ and ‘PKM’ fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767).
Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings.
Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. 
Speedfit products, when used indoors, are not affected by sunlight. 
When used outdoors protect from ultra violet light by lagging or painting.
It is recommended that all installations are checked prior to use to determine that a seal has been made.

Push-fit Solution for Plumbing & Heating Systems - Pipe Clips

22mm WHITE PIPE CLIP

Kennedy

Pressure Range:	1 to 10 bar. Temperature Range: 0°C to +80°C.

Bi-Directional
Pressure range:	+1 to +10 bar.
Temperature range: 0 to +80°C.

Flow Regulators

FR1-1 BI-DIRECTIONAL FLOW REGULATOR G1/8

FR1-2 BI-DIRECTIONAL FLOW REGULATOR G1/4

In-line Flow Restrictor
Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer. Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: -0.9bar min to +10bar max. Temp range: -20°C min to +70°C max. Tube suitability: Nylon, polyurethane.

Push-Fit Pneumatic Fittings - In-line Flow Restrictor

KFR4 KEN-FIT IN-LINE FLOW RESTRICTOR 4mm

Out-flow Restrictor to Male Taper
Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer. Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: -0.9bar min to +10bar max. Temp range: -20°C min to +70°C max. Tube suitability: Nylon, polyurethane.

Push-Fit Pneumatic Fittings - Out-flow Restrictor to Male Taper

KFRE6-3MT K/FIT O/F REST.6mm-G3/8 M/T

KFRE8-1MT K/FIT O/F REST.8mm-G1/8 M/T

KFRE10-2MT K/FIT O/F REST . 10mm-G1/4 M/T

KFRE12-3MT K/FIT O/F REST . 12mm-G3/8 M/T

Out-flow Restrictor to Male Taper
Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer. Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: -0.9bar min to +10bar max. Temp range: -20°C min to +70°C max. Tube suitability: Nylon, polyurethane.

MT = Male Taper Thread

In-flow Restrictor to Male Taper
Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer. Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: -0.9bar min to +10bar max. Temp range: -20°C min to +70°C max. Tube suitability: Nylon, polyurethane.

MT = Male Taper Thread

Push-Fit Fittings

John Guest Speedfit

15x15x10mm SPEEDFIT REDUCING TEE

John Guest Speedfit

22mm WHITE PIPE CLIP

Kennedy

FR1-1 BI-DIRECTIONAL FLOW REGULATOR G1/8

2 Variations

Kennedy

FR1-2 BI-DIRECTIONAL FLOW REGULATOR G1/4

2 Variations

Kennedy

KFR4 KEN-FIT IN-LINE FLOW RESTRICTOR 4mm

Kennedy

KFRE6-3MT K/FIT O/F REST.6mm-G3/8 M/T

4 Variations

Kennedy

KFRE8-1MT K/FIT O/F REST.8mm-G1/8 M/T

4 Variations

Kennedy

KFRE10-2MT K/FIT O/F REST . 10mm-G1/4 M/T

4 Variations

Kennedy

KFRE12-3MT K/FIT O/F REST . 12mm-G3/8 M/T

4 Variations

Kennedy

KFRT6-1MT K/FIT I/F REST. 6mm-G1/8 M/T

5 Variations

Kennedy

KFRT6-2MT K/FIT I/F REST.6mm-G1/4 M/T

5 Variations

Kennedy

KFRT8-1MT K/FIT I/F REST.8mm-G1/8 M/T

5 Variations

Kennedy

KFRT8-2MT K/FIT I/F REST.8mm-G1/4 M/T

5 Variations

Kennedy

KFRT10-2MT K/FIT I/F REST . 10mm-G1/4 M/T

5 Variations

Key Information

Group Policies

© 2024 TED. All rights reserved.Producer Register Limited Number: IE01113WB

© 2024 TED. All rights reserved.
Producer Register Limited Number: IE01113WB